Inferring paleostresses from natural fracture patterns: A new method

Geology ◽  
1989 ◽  
Vol 17 (4) ◽  
pp. 345 ◽  
Author(s):  
Jon Olson ◽  
David D. Pollard
Keyword(s):  
New Method ◽  
Natural Fracture ◽  
Fracture Patterns

Numerical Simulation of Complex Fracture Network Development by Hydraulic Fracturing in Naturally Fractured Ultratight Formations

2013 ◽  
Author(s):  
Hannes Hofmann ◽  
Tayfun Babadagli ◽  
Günter Zimmermann
Keyword(s):  
Fracture Network ◽  
Natural Fracture ◽  
Fracture Networks ◽  
Network Development ◽  
Complex Fracture ◽  
Fracture Patterns ◽  
Fracture Systems ◽  
Fracture Development ◽  
Complex Fracture Network ◽  
Treatment Designs

The creation of large complex fracture networks by hydraulic fracturing is imperative for enhanced oil recovery from tight sand or shale reservoirs, tight gas extraction, and Hot-Dry-Rock (HDR) geothermal systems to improve the contact area to the rock matrix. Although conventional fracturing treatments may result in bi-wing fractures, there is evidence by microseismic mapping that fracture networks can develop in many unconventional reservoirs, especially when natural fracture systems are present and the differences between the principle stresses are low. However, not much insight is gained about fracture development as well as fluid and proppant transport in naturally fractured tight formations. In order to clarify the relationship between rock and treatment parameters, and resulting fracture properties, numerical simulations were performed using a commercial Discrete Fracture Network (DFN) simulator. A comprehensive sensitivity analysis is presented to identify typical fracture network patterns resulting from massive water fracturing treatments in different geological conditions. It is shown how the treatment parameters influence the fracture development and what type of fracture patterns may result from different treatment designs. The focus of this study is on complex fracture network development in different natural fracture systems. Additionally, the applicability of the DFN simulator for modeling shale gas stimulation and HDR stimulation is critically discussed. The approach stated above gives an insight into the relationships between rock properties (specifically matrix properties and characteristics of natural fracture systems) and the properties of developed fracture networks. Various simulated scenarios show typical conditions under which different complex fracture patterns can develop and prescribe efficient treatment designs to generate these fracture systems. Hydraulic stimulation is essential for the production of oil, gas, or heat from ultratight formations like shales and basement rocks (mainly granite). If natural fracture systems are present, the fracturing process becomes more complex to simulate. Our simulation results reveal valuable information about main parameters influencing fracture network properties, major factors leading to complex fracture network development, and differences between HDR and shale gas/oil shale stimulations.

Numerical Investigation of Complex Hydraulic Fracture Development in Naturally Fractured Reservoirs

2015 ◽  
Author(s):  
Wu Kan ◽  
Jon E. Olson
Keyword(s):  
Fracture Propagation ◽  
Injection Pressure ◽  
Natural Fracture ◽  
Hydraulic Fractures ◽  
Differential Stress ◽  
Complex Fracture ◽  
Fracture Patterns ◽  
Fracture Development ◽  
Fracture Complexity ◽  
Shale Reservoirs

Abstract Complex fracture networks have become more evident in shale reservoirs due to the interaction between pre-existing natural and hydraulic fractures. Accurate characterization of fracture complexity plays an important role in optimizing fracturing design, especially for shale reservoirs with high-density natural fractures. In this study, we simulated simultaneous multiple fracture propagation within a single fracturing stage using a complex hydraulic fracture development model. The model was developed to simulate complex fracture propagation by coupling rock mechanics and fluid mechanics. A simplified three-dimensional displacement discontinuity method was implemented to more accurately calculate fracture displacements and fracture-induced dynamic stress changes than our previously developed pseudo-3d model. The effects of perforation cluster spacing, differential stress (SHmax - Shmin) and various geometry natural fracture patterns on injection pressure and fracture complexity were investigated. The single stage simulation results shown that (1) higher differential stress suppresses fracture length and increases injection pressure; (2) there is an optimal choice for the number of fractures per stage to maximize effective fracture surface area, beyond which increasing the number of fractures actually decreases effective fracture area; and (3) fracture complexity is a function of natural fracture patterns (various regular pattern geometries were investigated). Natural fractures with small relative angle to hydraulic fractures are more likely to control fracture propagation path. Also, natural fracture patterns with more long fractures tend to increase the likelihood to dominate the preferential fracture trend of fracture trajectory. Our numerical model can provide a physics-based complex fracture network that can be imported into reservoir simulation models for production analysis. The overall sensitivity results presented should serve as guidelines for fracture complexity analysis.

Numerical Simulation of Complex Fracture Network Development by Hydraulic Fracturing in Naturally Fractured Ultratight Formations

2014 ◽  
Vol 136 (4) ◽  
Author(s):  
Hannes Hofmann ◽  
Tayfun Babadagli ◽  
Günter Zimmermann
Keyword(s):  
Fracture Network ◽  
Natural Fracture ◽  
Fracture Networks ◽  
Network Development ◽  
Complex Fracture ◽  
Fracture Patterns ◽  
Fracture Systems ◽  
Fracture Development ◽  
Complex Fracture Network ◽  
Treatment Designs

The creation of large complex fracture networks by hydraulic fracturing is imperative for enhanced oil recovery from tight sand or shale reservoirs, tight gas extraction, and hot-dry-rock (HDR) geothermal systems to improve the contact area to the rock matrix. Although conventional fracturing treatments may result in biwing fractures, there is evidence by microseismic mapping that fracture networks can develop in many unconventional reservoirs, especially when natural fracture systems are present and the differences between the principle stresses are low. However, not much insight is gained about fracture development as well as fluid and proppant transport in naturally fractured tight formations. In order to clarify the relationship between rock and treatment parameters, and resulting fracture properties, numerical simulations were performed using a commercial discrete fracture network (DFN) simulator. A comprehensive sensitivity analysis is presented to identify typical fracture network patterns resulting from massive water fracturing treatments in different geological conditions. It is shown how the treatment parameters influence the fracture development and what type of fracture patterns may result from different treatment designs. The focus of this study is on complex fracture network development in different natural fracture systems. Additionally, the applicability of the DFN simulator for modeling shale gas stimulation and HDR stimulation is critically discussed. The approach stated above gives an insight into the relationships between rock properties (specifically matrix properties and characteristics of natural fracture systems) and the properties of developed fracture networks. Various simulated scenarios show typical conditions under which different complex fracture patterns can develop and prescribe efficient treatment designs to generate these fracture systems. Hydraulic stimulation is essential for the production of oil, gas, or heat from ultratight formations like shales and basement rocks (mainly granite). If natural fracture systems are present, the fracturing process becomes more complex to simulate. Our simulations suggest that stress state, in situ fracture networks, and fluid type are the main parameters influencing hydraulic fracture network development. Major factors leading to more complex fracture networks are an extensive pre-existing natural fracture network, small fracture spacings, low differences between the principle stresses, well contained formations, high tensile strength, high Young’s modulus, low viscosity fracturing fluid, and large fluid volumes. The differences between 5 km deep granitic HDR and 2.5 km deep shale gas stimulations are the following: (1) the reservoir temperature in granites is higher, (2) the pressures and stresses in granites are higher, (3) surface treatment pressures in granites are higher, (4) the fluid leak-off in granites is less, and (5) the mechanical parameters tensile strength and Young’s modulus of granites are usually higher than those of shales.

New constraints on stress and fracture orientations in the Shipwreck Trough, Otway Basin: implications for conventional and unconventional exploration and production

2012 ◽  
Vol 52 (2) ◽  
pp. 697
Author(s):  
David Tassone ◽  
Simon Holford ◽  
Rosalind King ◽  
Guillaume Backé
Keyword(s):  
Stress Tensor ◽  
Test Data ◽  
Sedimentary Basins ◽  
Horizontal Stress ◽  
In Situ Stress ◽  
New Method ◽  
Natural Fracture ◽  
Log Data ◽  
Maximum Horizontal Stress

A detailed understanding of the in-situ stress tensor within energy-rich basins is integral for planning successful drilling completions, evaluating the reactivation potential of sealing faults and developing unconventional plays where fracture stimulation strategies are required to enhance low permeability reservoirs. Newly available leak-off test results interpreted using a new method for analysing leak-off test data constrains the minimal horizontal stress magnitude for the offshore Shipwreck Trough wells to be ∼20 MPa/km, which is similar to the vertical stress magnitude derived from wireline data for depths shallower than ∼2–2.5 km. Breakouts interpreted from image log data reveal a ∼northwest–southeast maximum horizontal stress orientation and formation pressure tests confirm near-hydrostatic conditions for all wells. The new method for analysing leak-off test data has constrained the upper limit of the maximum horizontal stress magnitude to be the greatest, indicating a reverse-to-strike-slip faulting regime, which is consistent with neotectonic faulting evidence. Petrophysical wireline data and image log data to characterise extant natural fracture populations within conventional reservoirs and stratigraphic units that may be exploited as future unconventional reservoirs have also been used. These fracture sets are compared with possible fracture populations recognised in contiguous, high-fidelity 3D seismic datasets using a new method for identifying fracture systems based on attribute mapping techniques. This study represents the first of its kind in the Otway Basin. Combined analysis of the in-situ stress tensor and fracture density and geometries provides a powerful workflow for constraining fracture-related fluid flow pathways in sedimentary basins.

scholarly journals Natural fracture distribution and a new method predicting effective fractures in tight oil reservoirs in Ordos Basin, NW China

2016 ◽  
Vol 43 (5) ◽  
pp. 806-814 ◽  
Author(s):  
Jianming FAN ◽  
Xuefeng QU ◽  
Chong WANG ◽  
Qihong LEI ◽  
Liangbing CHENG ◽  
...  
Keyword(s):  
Ordos Basin ◽  
Oil Reservoirs ◽  
New Method ◽  
Natural Fracture ◽  
Tight Oil ◽  
Nw China ◽  
Tight Oil Reservoirs ◽  
Fracture Distribution

scholarly journals A New Method for Fracturing Wells Reservoir Evaluation in Fractured Gas Reservoir

2014 ◽  
Vol 2014 ◽  
pp. 1-12 ◽  
Author(s):  
Jianchun Guo ◽  
Yong Xiao ◽  
Haiyan Zhu
Keyword(s):  
Evaluation Model ◽  
New Method ◽  
Natural Fracture ◽  
Fuzzy Arithmetic ◽  
Fuzzy Evaluation ◽  
Natural Fractures ◽  
Gas Reservoir ◽  
Reservoir Evaluation ◽  
Gray Correlation ◽  
Fuzzy Logic Theory

Natural fracture is a geological phenomenon widely distributed in tight formation, and fractured gas reservoir stimulation effect mainly depends on the communication of natural fractures. Therefore it is necessary to carry out the evaluation of this reservoir and to find out the optimal natural fractures development wells. By analyzing the interactions and nonlinear relationships of the parameters, it establishes three-level index system of reservoir evaluation and proposes a new method for gas well reservoir evaluation model in fractured gas reservoir on the basis of fuzzy logic theory and multilevel gray correlation. For this method, the Gaussian membership functions to quantify the degree of every factor in the decision-making system and the multilevel gray relation to determine the weight of each parameter on stimulation effect. Finally through fuzzy arithmetic operator between multilevel weights and fuzzy evaluation matrix, score, rank, the reservoir quality, and predicted production will be gotten. Result of this new method shows that the evaluation of the production coincidence rate reaches 80%, which provides a new way for fractured gas reservoir evaluation.

scholarly journals Terrestrial photogrammetry: a method to gather data on fractures for DFN modelling from exposed rock surfaces

2021 ◽  
Vol 1 ◽  
pp. 61-62
Author(s):  
Filip Loeckle
Keyword(s):  
Open Source ◽  
Focal Length ◽  
Point Clouds ◽  
Distribution Functions ◽  
Natural Fracture ◽  
Rock Surface ◽  
Fracture Surfaces ◽  
Exposed Rock ◽  
Fracture Patterns ◽  
Terrestrial Photogrammetry

Abstract. The stochastic generation of discrete fracture networks (DFN) is a method for modelling fracture patterns used to assess the in situ fragmentation in a volume of rock. The DFN modelling approach is based on the assumption that the natural fragmentation of rocks is a function of the length and connectivity of the fractures within the considered volume of rock. Thus, in order to generate a site-specific DFN, the primary geometric properties of the fracture surfaces within the rock volume (especially orientation, size and fracture intensity as well as the local spatial variability) must be defined as distribution functions (Elmo et al., 2014). The required base statistics are usually obtained from fracture analysis on boreholes, exposed rock surfaces or (to a limited extent) 3D seismics (e.g. Bisdom et al., 2014; Bemis et al., 2014). We adopted a terrestrial close-range photogrammetry approach to capture several outcrops and analyse fracture traces on the exposed rock surfaces, the chosen workflow is based around the use of free and open-source software. Images were acquired from several quarries in the Weschnitzpluton, a granodioritic to quartz monzodioritic pluton in the Bergstrasse Odenwald (e.g. Altherr et al., 1999) using a consumer-grade Nikon D5300 DSLR with fixed focal length instead of a drone or Lidar-system for legal reasons, partially tree-lined outcrops and cost efficiency. Since point clouds obtained from photogrammetry are inherently dimensionless, we used a spherical target with compass and bubble level for scale and proper spatial orientation (Froideval et al., 2019). The exact geolocation is not particularly important for the task, so the use of GPS, total station or georeferenced ground control points is not necessary. Dense point clouds were computed using the open source SfM photogrammetry suite Meshroom (AliceVision, 2021), which can be used for manual or semi-automatic detection of fracture surfaces and their orientation (Schnabel et al., 2007) and to generate orthorectified images of the rock surface to trace fracture lengths and nodes in a GIS (Nyberg et al., 2018). Our investigations proved terrestrial photogrammetry to be a valuable and easily accessible tool in the documentation of natural fracture patterns and a robust base for the generation of DFN networks.

Sign in / Sign up

Export Citation Format

Share Document